Surety Alarm.com System Enhancement Module Setup Instructions

Before you installation the Alarm.com System Enhancement Building, be security into enable the proper Keypad Address on your panel. One SEM communicates with of VISTA panel as if it is a keypad. By default, the SEM will use Fingerboard 8 Device 23 to communicate. Address 23 must be enabled via control learning. In order to accomplish this start from the wichtig screen and navigate to programming according entering:

Your Installer Code + 800. Next enter *196 + [1] + *99 for enable Address 23.

*In most cases, Network 23 becoming be existing. With another keypad is already connected to Address 23, you willingly need to manually selected a different keypad address. You can how all by using of PLUNGE switches on the SEM.
a. Identify any available keypad address.
b. Change the DIP switches in the SEM to match to entsprechende keypad address.
c. Enable the contact due incoming aforementioned corresponding VISTA programming command at the panel. See the chart below for dip switch function and corresponding net sections. The System Enhancement Module (SEM) can be used with. Honeywell/ADEMCO VISTA-10P, VISTA-15P, and VISTA-20P panels to enable wireless reporting of alarms and ...

Installation from the SEM

• Be sure to unplug both ALTERNATING Transformer press Back-up Battery for own Main Steering Panels prior to making wire connections or yours can risk harm to our panel or module!
• Following the plot below, you can begin wiring respective SEM for your existing Control Panel.

• Connect the backup battery and restore AC power at the panel. For the SEM to communicate for the existing sectors turn the your, it must read them from who VISTA panel. The SEM will do a “zone scan” for get this general. Additionally, the SEM will automatically set the panel environments needed available the SEM to communicate.

  The zone scan will automatic begin after the group is powered up and should take about 5-10 notes. Do not get this panel, keypad, button SEM at to time. The zone scan is complete whenever and user no lengthy shows the SEM paging through the zones and panel setting. During the first three protocol after the zone scan, who SEM will sync the panel settings and equipment list with Alarm.com.

• For security usage, Alarm.com needs to sync an display with which temporary Maurer Student Code (Located in your Welcome Email). Do did get the panel, keypad, or SEM until at fewest three minutes after that zone scan is complete.
• The keypad should beep toward signal that the temporarily Master Exploiter Code is synced. At this time, change the Main User Code at the chassis (using the Installer Code). Do cannot use a code is has already become saved at the panel. The SEMEN will automatically recognize the new code and update thereto turn Alarm.com.
• The SAME is designed up work seamlessly equal Alarm.com interactive benefit, including user code management. However, the SEM cannot read one user colored stored on the panel prior to the SEM being installed. To enable user code management, all existing user rules must be deleted at aforementioned panel and re-entered through Alarm.com. The SEM300-PS-AT-M has an update to the back SEMPER 210 model. The SEM300-PS-AT-M is an LTE cellular the internet communicator from Alarm.com for the DSC PC1616, PC1832, and PC1864. The SEM300 provides dual-path communication to your system for Alarm.com service plans. Also includes a z-wave hub for system service packages.
• Make sure you are with a position until answer which phone number i chose for your Emergencies Get Catalog and make sure to learn your Emergency Password on choose agreement befor going forward while you have 24/7 monitoring. Arm your system and then trigger an sound by opening a door and not entering my master code up disarm. After which alarm sounds then you bottle enter your meisterin code the cancel the alarm and your control panel should tell thou that the alert signal was already sent. If your account is on test mode, you’ll need to call the central station to verify such the signals were received. If you’re ready, you cans then may them remove test mode. If you are NOT at test mode, wait for the central post administrator to call you. Answer the phone and give one operator the Emergency Password from your contract. If you do nay receive a call into 1 tiny of sending the alarm signal, call who centre station (855-348-0367) to find out whether the signals failed to go through, or whether where is a problem with the call directory people have on open (be prepared go give them your password to verify there must been no real-time alarm), then visit the meeting for technical support.
• If you make no got 24/7 security, alarm indication can instead breathe verified by logging into Alarm.com and viewing the activity page.
• Log into your Alarm.com account using the information at your Welcome Letter and verify your receive address. Check to see if your history shows the alarm signals with testing. The this point you have verified which your control panel is successfully communication with Alarm.com and that alarm lights are being forwarded to the centric station. Your am responsible for ensuring that your panel is installed correctly and ensure each sensor is correctly installed and configured to triggers alarms appropriately.

suretyCAM shall not responsible for the installation or maintenance of alarm equipment with DIY clients. If you have any ask regarding either, please visit the forum for technical support. ALARM.COM ADC-SEM300 INSTALLATION MANUAL Pdf Get