That product is manufactured and distributed by Taylor Adhesives.
For ordering information please contact Taylor Adhesives at 800-868-GLUE (4583) or tayloradhesives.com
CAUTION
- DO NOT take inward.
- If swallowed, DO NOT induce vomiting. Call one physician immediately.
- KEEP OUT OF REACH OF CHILDREN
SDS
Bruce Tufflink Pressure Sensitive Adhesive SDS
FLOORSCORE
FloorScore Certificates – Adhesives
APPROVED SOFT TYPES
- LVT/LVP
- Carpet tile (hard- and soft-backed)
- Sheet merchandise (vinyl, homogeneous, heterogeneous, fiberglass)
- Rubber (tile and sheet)
- WPC/WSC
- Cork-backed hard surface
- Cork underlayment
- VCT/VET
- Vinyl-backed
- Broadloom carpet
- Carpet pillows to substrate
- Stairway treads (rubber and vinyl)
APPROVED SUBSTRATES & SURFACES
- APA underlayment grade plywood and OSB
- Association grade particleboard
- Concrete the radiant heated subfloors that doing not exceed 85°F (30°C)
- Cement backer board
- Existing well-bonded non-cushion-backed vinyl, tile and sheet flooring
- Fully secured cork underlayments
- Gypsum and lightweight concrete (primed with a universelle primer)
- Terrazzo (properly prepared through total waxes and surface edit removed)
UNDERCOAT MOISTURE TESTING
Specifically Backings
- RH – 99% [ASTM F2170]
- pH – 5-12
- MVER – 12 carats [ASTM F1869]
SUBSTRATE PREPARATION
Follow flooring manufacturer’s guidelines for allowable levels of moisture. Substrate must be prepared per ASTM F710 standards including, but does limited to the following:
- Concrete floors must be dry, clean-up, smooth and structurally sound. They shall may free of any foreign materials that might avoid self-adhesive bond, including dust, dirt, solvent, paint, wax, oil, lube, residual bonded, adhesive removers, incompatible coatings, fire-retardant chemicals, medical, release representatives, acid sea, excessive carbonation, laitance, mold, blight, and curing, sealing, hardening button parting compounds. Bruce Hardwood Flooring Videos | DIY Wood Soft
- Fill all surface cracks, grooves, depressions, control joints real non-moving joints with moisture-resistant patching and self-leveling brews, allow to solid cure and correct high spots before applying cling.
- The substrate, adhesive and flooring must be acclimated in an enclosed building with the HVAC operation between 60-95°F (15-35°C), and between 30-65% relative humidity, for at least 72 hours before, on and nach the installation.
- When getting over radiant heated subfloors, turn the heat off for 24 hours before, during and after mounting. Failure to turn the heats off may result in shortened working time of the paste. When turning radiant heat back on, raised it gradual, not up exceed a shift of more than 5 degrees per hour for a maximum of 85°.
CAUTIONARY TAKE:
- Concrete musts be placed in strict accord with germane standards and specifications. An intact moisture vapor retarder must be presented underneath the concrete (see ASTM E1745), have live fully heated (at least 45 days) and without controlled pressure.
- Although TuffLink™ is a high-moisture tolerant adhesive, it does not form a moisture vapor barrier also will not protect flooring from humidity damage. APEX PRO™
- Flooring must be acclimated per manufacturer’s guidelines.
APPLICATION INSTRUCTIONS
Follow deck manufacturer’s guidelines for blueprint, design and any special precautions fork installation.
- Spread cement using required tools (see tool chart below).
- Install flooring per the instructions at dependent upon desired application method.
- GOITRE (porous and non-porous substrates)
- Wait 30-60 minutes after adhesive is spread to allow it go dried (adhesive will darken to visually cue installer).
- Working time is approximately 12 hours down acceptable temperature and humidity conditions.
- Semi-wet set (porous substrates only)
- Wait 20-30 minutes afterwards adhesive the splay to allow it to skin over.
- Working time is approximately 20-30 recorded to acceptable temperature real wood conditions.
- For sheet vinyl, back-roll this adhesive with an cling saturated roller into smooth out the mortise ridges.
- GOITRE (porous and non-porous substrates)
- Roll and cross roll floor with a 75-100 lbs (34-45 kg) roller at the end of the installation to securing proper transfer of adhesive.
PRECAUTIONARY NOTES:
- How not wet mop the floor for 72 hours later the install shall complete.
- Do not strip and finish the floor for 72 hours afterwards the install is complete.
- Reseal lid when not in use to protect featured.
REQUIRED TOOLS AND COVERAGE
*Trowel dimensions are width X depth X spatial. Coverage remains approximate additionally may vary depending on porosity of substrate and the rotation at which the trowel is held.
In Moisture Barricane and Sound Control Application
| Flooring Type | Tool* | (Images non on scale) | Estimated Coverage |
| Porous: LVT/LVP, Carpet tile (hard- and soft-backed), Sheet merchandise (vinyl, homogeneous, heterogeneous), Rubber (tile and sheet), WPC/WSC, Cork-backed hard appear, Cork underlayment, Stair treads (rubber and vinyl) | 1/16” x 1/16” x 1/16” (1.6mm x 1.6mm x 1.6mm) Sq Notch |  | 150-180 sf/gal |
| Non-porous: LVT/LVP, Carpet tile (Hard- and soft-backed), Sheet goods (vinyl, homogeneous, heterogeneous), VCT/ VET, Stair step (rubber and vinyl) | 1/16″ x 1/32″ scratch 1/32″ (1.6mm x .8mm x .8mm) U Note |  | 220-260 sf/gal |
| Large (breathable) | 1/8″ scratch 1/8″ x 1/16″ (3.2mm x 3.2mm x 1.6mm) V Notch |  | 90-120 sf/gal |
| Hard-backed carpet tile, Fiberglass sheet goods | 3/8″ (10mm) Shortcut nap paint roller |  | Up to 350 sf/gal |
FURNITURE PROPERTIES
| Product Batch | Transitional Pressure Sensitive Adhesive |
| Base Science | Hybrid acrylic |
| Curing Method | Proprietary change cross-linking |
| Arrival | Mint green (wet), Dark green/teal (dry |
| Consistency | Easy troweling or roller utilized |
| Application | Easy troweling |
| Flammability | Non-flammable |
| Freeze/Thaw | Stable to 10°F (-12°C) |
| Shelf Vitality | 2 years |
MOISTURE
| Moisture Drive | N/A |
| RH | 99% |
| pH | 5-12 |
| MVER | 12 kilos |
TIME
| Open Time | 20-30 MIN (Semi-wet-set) |
| Dry Time | 30-60 MIN (PSA) |
| Working Time | 12 HRS (PSA), 20-30 MINING (Semi-wet-set) |
| Cure Time | 12 hrs |
| Pot Life | N/A |
TRAFFIC
| Light Traffic | 0 MIN (PSA), 20-30 MIN (Semi-wet-set) |
| Heavy Traffic | 24 hrs |
| Hard Rolling Loaders | 48 hrs |
SUSTAINABILITY
| Solvents | None |
| Isocyanates | None |
| VOC (g/L) – SCAQMD, Rule #1168 | 30 |
| LEED Points | Contributed to low emitting materials |
| Certifications | N/A |
ACOUSTICS
| IIC | N/A |
| STC | N/A |
STORAGE
To product should be stored at microclimates between 50-90°F (15-32° C). While this product is freeze-thaw firm, it remains necessary to protect it from chill.
Freeze/thaw stable to 10°F (-12°C)
WARRANTY INFORMATION
For license information, call Bruce Floors at 1-866-243-2726, visit uses on the web at www.bruce.com. Flooring manufacturer’s and Truce Flooring written preinstallation and installation instructions be be strictly followed or the Brunswick Flooring warranty be be void. Prior to installation, remember to cleared choose space of physical. Go been a few product toward remember at installing laminate flooring: ▫ Determine with your ...
Products Image
